If you’re tired of hearing the fan make a noise every time you turn it on, you may want to consider cleaning the motor. You may not think about cleaning your fan motor often, but keeping the area around it free from dust and dirt is important. A clean motor can help your fan run more efficiently and last longer.
The good news is that this isn’t a hard job at all, but it does require some special tools like a screwdriver and wire brush. That being said, if you have access to these items, then there’s no reason your fan shouldn’t be cleaned again in less than an hour!
This guide will show you how to clean a fan motor in four easy steps.
Read more: How to Clean a Fan?
How to clean a fan motor?
Step 1: Remove the grille, blades, and canopy to clean a ceiling fan. Then use a vacuum to remove dust and debris from all accessible surfaces.
Step 2: Remove small parts of the motor with a paintbrush or compressed air.
Step 3: Clean all accessible surfaces using soap and water, followed by a dry cloth or paper towel dampened with rubbing alcohol (this will help kill any germs).
Read more: How to Clean Table Fan?
Disconnect the wires and remove the canopy
You’ll need to disconnect the wires and remove the canopy to begin cleaning your fan motor. The first step is to remove any screws holding on the canopy. Then, loosen them with a screwdriver if they’re too tight or break off if they’re not loose enough. Once you’ve removed all these screws, gently pull off the canopy while holding onto it as much as possible so you don’t lose any pieces that might fall out.
Next, unplug all wiring connected to your fan motor (this usually involves removing one or more wires from each side). Now that everything has been disconnected from both sides of your motor disassemble those parts by unscrewing them from one another until nothing remains but their components (blades, motors, etc.).
Read more: How to Clean a Hibachi Grill?
Remove the blades from the fan
Use a screwdriver to remove the blade screws to remove the blades first. Then, pull out each blade in a clockwise direction and ensure that you have removed all of them before proceeding to the next step.
Use a vacuum to take out dust and debris.
The first step is to clean the motor of dust and debris using a vacuum with a brush attachment. Next, use a crevice tool to get into hard-to-reach places. Finally, use a small paintbrush or compressed air to clean small parts of the motor.
Remove small parts of the motor with a small paintbrush or compressed air
To clean the motor:
- Use a little paintbrush or compressed air to clear dust and debris from the motor.
- Do not use any liquid solutions as they could damage it.
- Avoid using a vacuum cleaner as it could damage the motor.
- Clean it with a soft cloth if necessary, but do not let water enter any openings, as this can cause electrical problems in your fan!
Read more: How to Clean a Fan with a Plastic Bag?
Dry all surfaces thoroughly before replacing them in their original place
After all the parts have been cleaned, dry them thoroughly. Use a soft cloth to wipe away any moisture and then replace it in its original place. Avoid using anything that can leave fibers behind, such as paper towels.
Also, do not use a vacuum cleaner, as this will cause debris to fly off into the fan motor, which could clog up moving parts. Finally, do not try to dry it with a hairdryer or other heat source, as this can damage seals, bearings, and even electrical wiring over time!
Read more: When Must a Knife Be Cleaned and Sanitized?
Does cleaning a fan improve its performance?
It’s tempting to think that cleaning your fan motor will make it work better, but this is not the case. If you don’t know what you’re doing when cleaning a fan motor, you could cause more damage than good. For example, if your fan has been running for a long time without being cleaned, there could be dust and dirt on the inside of the motor casing, which can cause overheating problems or even electrical damage.
So if you have decided to clean your fan motor at home, then it is important not to rush into things as this could put you or others at risk of injury due to electrical shock from faulty wiring caused by incorrect cleaning methods applied in trying to make repairs by yourself that was never needed in the first place!
Can I wash the fan motor?
No, you cannot wash a fan motor.
Fan motors are made of plastic and are not designed to be washed. They will become damaged if exposed to water or any other liquid. The best way to clean a dirty fan motor is with a vacuum cleaner. If there is debris in the fan itself, use a paintbrush or compressed air to clean out small parts.
Conclusion:
Cleaning your fan motor takes little time as long as you’ve got the right tools. A dirty fan motor can impact how well your fan works and lead to its destruction.
You’ll be able to clean the motor in an hour rather than spend hours worrying about it not working as well as it used to. If you read up on how to clean a fan motor, you will also find that it’s not a job that can’t wait. You don’t have to wait until your fan breaks down completely before you decide to clean the motor. The best time to do it is regularly so that your fan keeps working at its best for many years.
So what are you waiting for? Get to cleaning!